SPC-1L

Sulfinert Passivated 1L Sample Cylinder

   In order to properly perform ISBT sampling method 1.0 "LIQUID CARBON DIOXIDE SAMPLING USING SMALL, PASSIVATED CYLINDERS WITH DIP TUBES", ALI offers the SPC-1L dip-tube equipped, 1L sampling cylinder. This cylinder is Sulfinert passivated to prevent “wall-adsorption” effects that can be experienced with volatile sulfur compounds and other trace CO₂ impurities. Proper use of an SPC-1L eliminates the need for cylinder weighing, which makes liquid CO₂ sampling both easier and safer to perform. All SPC-1L cylinders are leak checked/THC-tested to ensure cleanliness (a 20 psig [138 kPa] N₂ charge is maintained) and are shipped ready-to-use.

 Components

 -Sulfinert passivated needle valve [outlet] with 1800 psig [12,400 kPa] burst disk, Kel-F soft-tip stem, 1/4” NPT (F) port, + dip-tube (sized for a safe, 58% liquid CO₂ fill as per USA CGA G-6.3 “Carbon Dioxide Cylinder Filling & Handling Procedures”) + 1/4” brass pipe cap (M)/10” lanyard assembly. All parts documentation is included.

 -Sulfinert passivated 1 Liter cylinder, dual-ended, DOT-3A1800 rated, serial numbered + hydro-test date- stamped. A Dip-tube orientation decal is affixed. All parts documentation is included.

- Sulfinert passivated needle valve [inlet] with Kel-F soft-tip stem + 1/4” brass compression plug (F)/10” nylon-coated lanyard assembly. All parts documentation is included.

-Sulfinert passivated, "sacrificial" 1/4” NPT (M)-to-1/4" compression (M) fitting (assembled on SPC-1L inlet valve).

-Pictorial Sampling/Shipping Instructions for ISBT Method 1.0 sampling + proper HAZMAT shipping. 

 Maintenance Services

 ALI stocks all necessary replacement parts for the SPC-1L and can provide customers with periodic (5-yr. USA) cylinder re-inspection, hydrostatic re-test / re-certification services, as per USA DOT requirements. Cylinder cleaning is also offered

 Recommended Accessories

-PDISK-1800: A 1800 psig [12,400 kPa] burst disk replacement kit.

- NV1-Kit: A needle valve stem replacement kit

- 4NPTM-4C: Replacement Inlet fitting (1/4” NPT (M) to 1/4” Compression (M)

-SPRA-1800: A Sulfinert passivated, 1800 psig [12,400 kPa] pressure-relief assembly for interfacing ST-3 tubing to a CO₂ source-sampling valve. The SPRA-1800 is equipped with a 1/4" (F) inlet compression fitting and 1/4" (M) outlet compression fitting and is strongly recommended for ISBT sampling.

- ST-3: A Sulfinert & PTFE passivated, 3' [91 cm], high-pressure (3,000 psig [20,670 kPa]) rated, flexible ss sampling tubing with 1/4" compression fittings (F/F). The ST-3 is ideal for connecting an SPC-1L to a SPRA-1800 /liquid CO₂ source valve during ISBT sampling.

- CS-25: Cylinder Support, consisting of a heavy tripod base + 25" support rod + upper / lower cylinder clamps + safety lanyard. For secure, vertical mounting of an SPC-1L when used with a CO₂ analyzer.

- CRYGL-14: The safe sampling of liquid CO₂ requires several types of safety equipment including cryogenic gloves for handling liquid CO₂. ALI recommends these 14" long gloves for all ISBT CO₂ sampling methods.

- SAFE-T-SHIELD: This ergonomic face shield is recommended for all ISBT CO₂ sampling methods.

- VPR-120-90: (120 VAC, 60 Hz, 100 watts) Sulfinert passivated liquid CO₂ vaporizer - pressure regulator with a 1800 psig [12,400 kPa] pressure relief disk + 90^o outlet needle valve - pressure regulator configuration (specify a PR-20 [0-20 psig] or PR-60 [0-60 psig] regulator). This module is used for connecting an SPC-1L to CO₂ analyzers.

Purchase/ Terms of Payment/ Delivery Schedule

 Purchases can be made by phone / fax / e-mail using a Purchase Order (if ALI approved), major credit card (Visa, Mastercard, Discover, American Express), US Certified Check or E-Bank Transfer. Full payment must be received before shipment (unless PO authorized). Delivery typically requires 3 - 5 weeks after order placement.

 Please contact ALI if you have any questions or require a quotation

World Class Products & Professional Service